home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-17 / oad120.exe / README.IOM < prev   
Text File  |  1993-04-30  |  12KB  |  298 lines

  1.                                  README FILE
  2.                                 April 29, 1993
  3.  
  4.                              INSTALL version 1.20
  5.                            OAD DRIVER version 1.20
  6.                           OAD UTILITIES version 1.20
  7.  
  8.  
  9. ==============================
  10. INSTALLATION
  11.  
  12.        WINDOWS PROGMAN.INI AND OAD INSTALL 
  13.       When installing to Windows, INSTALL.EXE renames the original
  14.       PROGMAN.INI file to PROGMAN.BAK.
  15.  
  16. ==============================
  17. DRIVER
  18.  
  19.  
  20.     1.   DRIVER SWITCH
  21.            The following switch can be used with DOSCFG.EXE and
  22.           DOSOAD.SYS.
  23.  
  24.            /L = country : Set the current language to the country code
  25.           specified in "country" as specified by the DOS COUNTRY.SYS.
  26.  
  27.     2.   OAD DRIVER WITH PPA (PARALLEL PORT ADAPTER)
  28.  
  29.       a.    Security systems (such as Watchdog) can disable this adapter,
  30.            especially if the security system is loaded before DOSOAD.SYS.
  31.           
  32.       b.    When running DOSCFG.EXE from command line, drives connected
  33.            to a PPA may not be found.
  34.  
  35.     3.  DOSCFG.EXE IN HIGH MEMORY
  36.           Do not attempt to load DOSCFG.EXE into high memory.  It executes
  37.          and terminates, never staying resident in memory.
  38.  
  39.     4.  INCREASING THE SPEED OF THE BOOT SEQUENCE
  40.           In order to speed up the boot process on a computer in which the
  41.          drive configuration never changes, it is suggested that the /M1
  42.          switch be replaced with the /M0 switch.  If desired the 
  43.          DEVICE=\DOSOAD\DOSCFG.EXE line can be removed from the CONFIG.SYS
  44.          file, after the system has been configured.
  45.          If the configuration changes, reinsert the /M1 option.  
  46.  
  47.     5.  EMM386 RAM OPTION
  48.           When using EMM386 with the RAM option the DOSOAD.SYS driver must
  49.          be loaded into low memory.
  50.  
  51.     6.   1,024 Byte Sector SUPPORT
  52.           1,024 bytes/sector disks CAN NOT be made bootable.
  53.  
  54.     7.   IOMEGA 8-INCH BERNOULLI PRODUCTS are not supported at this time.
  55.  
  56.     8.    Adapter ROM Code level 10 or greater is required if booting from
  57.          an Iomega product.
  58.  
  59.  
  60. ==============================
  61. UTILITIES
  62.  
  63.     1.   OADUTIL.EXE SUPPORTS DOS 6.0 AND DISK COMPRESSION
  64.           This version of the utilities has been tested for 
  65.          compatibility with MicroSoft DOS 6.0 adn MicroSoft Double Space 
  66.          disk compression.
  67.  
  68.       a.  REMOVING THE DISK COULD RESULT IN LOST OR DAMAGED DATA.
  69.            Because of the Doublspace limitations, IOMEGA recommends using
  70.           DoubleSpace compression only on locked write enabled media. 
  71.  
  72.     2.   OADUTIL.EXE MEMORY USAGE
  73.           The menu mode of OADUTIL.EXE requires about 480K of free memory.
  74.          Less memory is required when running in command-line mode.
  75.  
  76.     3.   DESQVIEW AND OADUTIL.EXE
  77.           OADUTIL.EXE will not run in DESQVIEW.
  78.  
  79.     4.   VIDEO ADAPTERS
  80.           The following switches can be used on OADUTIL.EXE command 
  81.          line to force a more readable video interface.
  82.  
  83.            /VGA12   - color vga graphics 
  84.            /VGA11   - monochrome vga graphics 
  85.            /TEXT    - color text
  86.            /LCD     - monochrome text
  87.  
  88.     5.   MOUSE PROBLEMS
  89.  
  90.           a.   NO MOUSE DRIVER
  91.                 The mouse driver needs to be loaded.
  92.  
  93.           b.   ROM BIOS
  94.                 If the ROM BIOS is loaded into shadow RAM, the mouse 
  95.                driver may have problems.
  96.  
  97.           c.   WINDOWS 3.x
  98.                 If the OADUTIL.EXE is run under Windows and the mouse is
  99.                not present, it may be for one of two reasons:
  100.  
  101.                -    The mouse driver needs to be loaded before running 
  102.                     Windows.
  103.  
  104.                -    With Windows 3.1, the mouse driver may be an older
  105.                      version.
  106.  
  107.           d.   SWITCHING APPLICATIONS
  108.                 Switching between OADUTIL.EXE and other Windows 
  109.                applications may cause multiple mouse pointers left on 
  110.                the OADUTIL.EXE desktop.
  111.  
  112.     6.   STARTING THE OADUTIL.EXE WITHIN WINDOWS
  113.           When running OADUTIL.EXE under Windows, always start 
  114.          OADUTIL.EXE by clicking the Iomega OAD Utility icon.
  115.  
  116.     7.   SURFACE VERIFY FORMAT WITH ADAPTEC ADAPTERS USING ASPIxDOS.SYS
  117.           When doing a 'Format (long) with Surface Verify' the thermometer
  118.          bar will only be updated upon completion of the format.  The time
  119.          shown to complete the format is approximate.
  120.  
  121.     8.   OADUTIL.EXE  "Disk Copy" FUNCTION
  122.           You can now copy to and from DOS formatted floppy and 
  123.          hard disks.
  124.  
  125.           Things to be aware of:
  126.               a.  The OAD Utilities "Disk Copy" function copies only DOS
  127.                  formatted disks.
  128.  
  129.               b.  The OAD Utilities "Disk Copy" function will erase all
  130.                  data on the destination disk unless "Append Copy" is
  131.                  selected in the Disk Copy dialogue or by "/A" switch on
  132.                  command line.
  133.                  "Append Copy" allows you to append one disk to another. 
  134.                  You may specify a destination path where you would like 
  135.                  to copy to.
  136.                  As an example, you might want to copy E: to a 
  137.                  subdirectory on D:.  
  138.                  OADUTIL.EXE C E: D: /A:[subdirectory name]
  139.  
  140.               c.  The "Append Copy" will replace any files of the same
  141.                  name and add files that do not already exist.
  142.  
  143.     9.  LOCKING THE IOMEGA DRIVE TO INSTALL or RUN CERTAIN SOFTWARE
  144.          Some software will only install or run on a fixed disk.
  145.         In these cases it may be necessary to use the OAD Utilities LOCK
  146.         command.
  147.  
  148.     10. EJECTING A DISK WHEN THE READ/WRITE ACCESS LIGHT IS ON
  149.          Removing an Iomega disk when the access light is on is not 
  150.         recommended.
  151.  
  152.     11. OAD DOS AND OAD OS/2 DIRECTORY CONFLICTS
  153.          The Iomega OAD OS/2 and Iomega OAD DOS software drivers and
  154.         utilities can not reside in the same subdirectory.
  155.  
  156.     12. USING DOS FORMAT TO FORMAT IOMEGA DISKS
  157.          The DOS Format command can be used to format Iomega disks only
  158.         if they have previously been formatted using the OAD Utilities.
  159.  
  160.     13. MAKING A BOOTABLE DISK WITH DR DOS 6.0.
  161.          When DR DOS 6.0 FORMAT.EXE is used to format a Iomega Disk, the
  162.         '/S' switch will not make the disk bootable.  You will need to
  163.         use the OAD Utility Format with the 'Copy System' option to make
  164.         a bootable DR DOS 6.0 Iomega disk.  Refer to the 'Disk Format'
  165.         section in chapter 3 of the User's Manual for more information,
  166.         and instructions on formatting from the command line.
  167.  
  168.     14. OAD UTILITIES DIAGNOSTICS
  169.          The OAD Utilities Diagnostic option performs a number of
  170.         non destructive data tests on the drive and disk.  The disk
  171.         must not be write protected when using this diagnostic.
  172.         Refer to chapter 4 of the User's Manual for more information.
  173.  
  174. **============================
  175. MICROSOFT'S SMARTDRIVE
  176.  
  177.     1.  OAD DOS WITH SMARTDRIVE
  178.          OAD has been tested with MS-DOS Smartdrive.  No problems have
  179.         been reported with the SMARTDRIVE default.  If the default has 
  180.         been changed and Smartdrive is using the write caching feature,
  181.         do not remove the Bernoulli disk until the drive light is no 
  182.         longer flashing.  Removing the disk could result in lost or 
  183.         damaged data.
  184.  
  185.      2. INVALID UNIT ERROR
  186.          The error "INVALID UNIT" may be reported when using OAD with 
  187.         SMARTDRV.SYS loaded.  To correct this problem, add the /G option 
  188.         after SMARTDRV.SYS.
  189.             Example:  DEVICE=C:\DOS\SMARTDRV.SYS /G
  190.  
  191.  
  192. ==============================
  193. SPEEDCACHE+ (SCPLUS.EXE)
  194.  
  195.      1. SCPLUS.EXE SUPPORTS DOS 6.0 AND DISK COMPRESSION
  196.          This version of the utilities has been tested for compatibility
  197.         with MicroSoft DOS 6.0 and MicroSoft Double Space disk 
  198.         compression.
  199.      
  200.      2. SCPLUS USE WITH SECURITY SYSTEMS
  201.          Some security systems will not work with write-delay caching.
  202.         The default SCPLUS settings may have to be modified. (scplus -m)
  203.  
  204.      3. REBOOTING WITH SCPLUS LOADED
  205.          SCPLUS may not be able to trap <Ctrl Alt Del> to prevent a warm
  206.         boot during certain applications.  Be sure all disk accesses have
  207.         been completed before rebooting. 
  208.  
  209. ==============================
  210. BERNOULLI BACK-IT VERSION 1.3 
  211. RESTRICTIONS AND COMPATIBILITY
  212.  
  213.     A number of restrictions and compatibility issues regarding Bernoulli
  214.    Back-It version 1.3 are described in the README.TXT document located 
  215.    with the Bernoulli Back-It program in the \OADDOS\BBACKIT directory.
  216.  
  217.  
  218. ===============================
  219. NON-IOMEGA SCSI ADAPTER  SUPPORT
  220.  
  221.      1. OAD DRIVER WITH ADAPTEC ADAPTERS -
  222.          (1520, 1522, 1540(B or C), 1542(B or C), 1640, 1740, and 1742)
  223.  
  224.            a.   Load the ASPIxDOS.SYS (x=2,4 or E) driver before any
  225.                memory manager in the CONFIG.SYS file.
  226.  
  227.            b.   Remove the ASPIDISK.SYS loaded in the CONFIG.SYS file.
  228.  
  229.            c.   To ensure the system will be reconfigured during the next
  230.                boot, place the /M1 option in the DOSCFG.EXE device driver
  231.                line after the ASPIxDOS.SYS driver in the CONFIG.SYS file.
  232.  
  233.            d.   Load the DOSOAD.SYS before or after any memory manager 
  234.                and after the ASPIxDOS.SYS driver in the CONFIG.SYS file.
  235.  
  236.            e.   Reboot.
  237.  
  238.            f.   Iomega 8-inch 10MB and 20MB Bernoulli drives and 
  239.                5 1/4-inch 20MB Bernoulli drives are not supported.
  240.  
  241.            g.   Using DOS FORMAT.EXE to format a Iomega Disk with the 
  242.                '/S' switch may not make the disk bootable.  You will 
  243.                need to use the OAD Utility Format with the 'Copy System' 
  244.                option to make a bootable Iomega disk.
  245.  
  246.            h.   Users of Adaptec 1540C and 1542C adapters must load
  247.                ASPI4DOS.SYS before DOSCFG.EXE for proper function of
  248.                the Adaptec adapter.
  249.  
  250.      2. OAD DRIVER WITH IBM Host Bus Adapter (HBA)
  251.  
  252.            a.   When booting your computer make sure that your Iomega 
  253.                drives have the appropriate media and that it is spinning.
  254.  
  255.            b.    Iomega 8-inch 10MB and 20MB Bernoulli drives and 
  256.                 5 1/4-inch 20MB Bernoulli drives are not supported.
  257.  
  258.            c.    Using DOS FORMAT.EXE to format a Iomega Disk with the 
  259.                 '/S' switch may not make the disk bootable.  You will 
  260.                 need to use the OAD Utility Format with the 'Copy System'
  261.                 option to make a bootable Iomega disk.
  262.  
  263. ==============================
  264. IOMEGA U.S. AND INTERNATIONAL
  265. TELEPHONE NUMBERS
  266.  
  267.      o    Iomega customers located in the USA or Canada
  268.  
  269.           Iomega Customer Service and
  270.           Technical Support          (800) 456-5522
  271.           FAX                        (801) 778-3460
  272.           Iomega Bulletin Board
  273.           (settings 8,N,1)           (801) 778-4400
  274.           Compuserve(r)              Find Iomega
  275.           Internet                   info@iomega.com
  276.           AppleLink(tm)              Iomega.TS
  277.  
  278.  
  279.  
  280.      o    Iomega customers located in Europe
  281.  
  282.           Iomega (Freiburg, Germany) 49 (0) 761-45040
  283.           FAX                        49 (0) 761-4504414
  284.           (The following numbers are toll free within
  285.           the country listed)
  286.           Germany                    0130-824544
  287.           France                     05-904057
  288.           United Kingdom             0800-898563
  289.           Italy                      1678-78360
  290.           Belgium                    078-112117
  291.           Netherlands                06-0222967
  292.           Sweden                     020-795512
  293.  
  294.      o    All other locations worldwide
  295.  
  296.          Customers may call either the Freiburg, Germany office listed
  297.         above or Iomega headquarters in the USA at 801-778-3000.
  298.